necessary.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
If this is not done, when you make the next coees, the
grounds container may ll up more than expected and clog the
machine.
Cleaning the drip tray and condensate tray
Important!
If the drip tray is not emptied regularly, the water could
overow from the edge and seep inside or around the coee
maker. This could damage the machine, the surface it rests on
or the surrounding area.
The drip tray is tted with a level indicator (red) showing the
level of water it contains (g. 25).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned.
To remove the drip tray:
1. Remove the drip tray and the grounds container (g. 24);
2. Empty the drip tray and grounds container and wash
them;
3. Check the condensate tray and empty if necessary.
4. Replace the drip tray and grounds container.
Cleaning the inside of the coee maker
Danger of electric shock!
Before cleaning internal parts, the machine must be turned
o (see “Turning o”) and unplugged from the mains power
supply.Neverimmersethecoeemakerinwater.
1. Check regularly (about once a month) that the inside of
the appliance (accessible after removing the drip tray)
is not dirty. If necessary, remove coee deposits with a
sponge.
2. Remove the residues with a vacuum cleaner (g. 26).
Cleaning the water tank
Clean the water tank (A9) regularly (about once a month) with
a damp cloth and a little mild washing up liquid.
Cleaning the coee spouts
1. Clean the coee spouts with a sponge or cloth (g. 27).
2. Check the holes in the coee spout are not blocked.
If necessary, remove coee deposits with a toothpick (g.
28).
HEATING WATER
Danger of burns!
Never leave the machine unsupervised while delivering hot
water. Stop delivery of hot water as described below when the
cup is full. The hot water spout becomes hot while water is
being delivered and must be handled by the handle only.
1. possible to avoid splashes.
2. Turn the steam dial to the I position. Delivery begins.
3. Stop by turning the steam dial to the 0 position.
Please note :
If “Energy Saving” mode is active, you may have to wait a few
seconds before the hot water is delivered.
CLEANING
Cleaning the coee maker
The following parts of the machine must be cleaned regularly:
- coee grounds container (A13),
- drip tray (A17) and condensate tray (A14),
- water tank (A9),
- coee spouts (A12),
- pre-ground coee funnel (A6),
- inside of the machine (accessible after opening the infuser
door (A10))
- infuser (A11).
Important!
• Do not use solvents, abrasive detergents or alcohol to
clean the coee maker.
With De’Longhi superautomatic coee makers, you need
not use chemical products to clean the machine.
The descaler recommended by De’Longhi is made from
natural and completely biodegradable substances.
• Noneofthecomponentscanbewashedinadishwasher.
• Donotusemetalobjectstoremoveencrustationsorcoee
deposits as they could scratch metal or plastic surfaces.
Cleaning the coee grounds container
When the light ashes, the coee grounds container
must be emptied and cleaned.
Unless you clean the grounds container, the light will continue
to ash and the appliance cannot be used to make coee.
To clean (with the machine on):
• Removethedriptray(g.24),emptyandclean.
• Empty the grounds container and clean thoroughly to
remove all residues left on the bottom.
• Also check the condensate tray (red) and empty if
Cleaning the pre-ground coee funnel
Check regularly (about once a month ) that the pre-ground
coee funnel is not blocked. If necessary, remove coee
deposits.
Cleaning the infuser
The infuser (A11) must be cleaned at least once a month.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned o (see “Turning
the appliance o” on page 10).
2. Remove the water tank.
3. Open the infuser door (g. 29) on the right side.
4. Press the two red release buttons inwards and at the same
time pull the infuser outwards (g. 30).
Important!
Clean the infuser without using washing up liquid as it
could be damaged.
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
6. Clean coee residues from the support where the infuser
rests.
7. After cleaning, replace the infuser by sliding it onto the
internal support, then push the PUSH symbol fully in until
it clicks into place.
Please note :
Iftheinfuserisdiculttoinsert,beforeinsertion,adaptitto
the right size by pressing the two levers shown in the gure.
8. Once inserted, make sure the two red buttons have
snapped out.
Comments to this Manuals