INSTALLATION and SERVICE INSTRUCTIONSUSE and CARE INSTRUCTIONSdistributed byDèLonghiPty LtdBUILT-IN GAS HOBSDEGH60DEGH60ST DEGH60WT
10CONVERSION PROCEDURE (to convert to Natural gas or to ULPG)REPLACING THE INJECTORSThe conversion procedure must be carried out only by an authorised
11MINIMUM BURNER SETTING ADJUSTMENTCheck whether the flame spreads to all burner ports when the burner is lit with thegas tap set to the minimum posit
12ELECTRICAL REQUIREMENTS:WARNING: THIS APPLIANCE MUST BE EARTHED.CAUTION: Ensure that the power outlet is properly earthed before connecting theap
13USE and CARECAUTION: This appliance must be used only for the task it has explicitly been designed for,that is for domestic cooking of foodstuffs.
14 The electric ignition is incorporated inthe knobs This appliance is class 328765341CONTROL PANEL5. Triple-ring burner control knob (1)6. Left sem
15LIGHTING GAS BURNERS Check that the electricity is switched on to allow spark ignition. Make sure that all controls are turned to zero. The gas
16Lighting the burnersWITH ELECTRIC IGNITION (without safety cut-off valve) mod.DEGH60WT - DEGH60STTo light one of the burners, press and turn the cor
17COOKING HINTS FOR GAS HOBSBurners Pan diameterAuxiliary*12 - 14 cmSemi-rapid 16 - 20 cmTriple ring 24 - 28 cmWok max 36 cmThe burner must be chosen
18mod. DEGH60WT - DEGH60STFigure 15aCORRECT USE OF TRIPLE-RING BURNER The flat-bottomed pans are to be placed directly onto the pan-support. To use
19Cleaning and MaintenanceGENERAL TIPS Before cleaning the hob switch it off and wait for it to cool down. Clean with a cloth, hot water and soap or
2Dear Customer,Thank you for having purchased and given yourpreference to our product.The safety precautions and recommendations reportedbelow are for
20Figure 16 Figure 17CORRECT POSITIONING OF THE BURNERS It is very important to check that spreader F and cap C of the burner (seeFigures 16 and 17)
21CORRECT POSITIONING OF THE TRIPLE-RING BURNER The triple ring burner must be correctly positioned (see fig. 20); the burner ribmust be located in p
22SERVICE AND MAINTENANCEIf the ignition spark fails to ignite or does not light the gas, check the followingitems before calling our Customer Service
23Descriptions and illustrations in this booklet are given as simply indicative. The manufacturer reserves the right,considering the characteristics o
cod. 1103186 ß2
3IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FORUSE OF ELECTRICAL APPLIANCESUse of any electrical appliance implies the necessity to follow a series of
447035 min500550100580minFigure 1DIMENSIONS (Table 2):(Note: Also refer to Figure 1)General DimensionsWidth 580 mmDepth 500 mmDepth Below Mounting Sur
5750 mm35 mm min100 mm min500 mm450 mmFigure 2CLEARANCES:Installation clearances and protection of combustible surfaces shall comply with thecurrent l
6The installation shall comply with the dimensions in Figures 1 and 2, bearing in mindthat: A minimum clearance of 20 mm has to be kept between the b
7INSTALLATION (Refer to Figure 4):1. Spread out the gasket “C” over the workbench at the edge of the cut out tak-ing care to overlap the gasket at the
8GAS SUPPLY: This appliance is suitable for use with Natural Gas or ULPG. (Check the “gas type”sticker attached to the appliance). For Natural Gas t
9TABLE FOR THE CHOICE OF THE INJECTORSNatural gas ULPGTest Point Pressure [kPa] 1.0 2.75BURNERAuxiliary (A) 0.85 3.6 0.53 3.6Medium-speed burner (SR)
Comments to this Manuals